Home › Finance Calculators › Electricity Bill Calculator

Electricity Bill Calculator

This electricity bill calculator estimates your monthly electricity bill from the units (kWh) shown on your meter. It works the way Indian electricity boards (DISCOMs) charge: your units are priced slab by slab, a fixed charge is added, and electricity duty is charged on top. The slab rates below are sample rates — every state and board has its own tariff, so edit the slab table to match your board and the estimate will follow your real tariff.

Rate slabs — sample slabs are filled in. Change the limits and rates to your board's tariff (you will find it on the back of your bill or on your DISCOM website):

Units fromUnits up toRate (₹ per unit)
0
101
301
501Above

How to use this electricity bill calculator

  1. Find your units consumed on your last bill or meter reading and type them in — 1 unit means 1 kWh.
  2. Edit the slab table so the limits and rates match your electricity board's tariff. The sample slabs are only a starting point.
  3. Enter your fixed charge (the flat monthly amount on your bill) and your electricity duty percentage.
  4. Read the total, and check the slab-wise breakdown to see exactly where the money goes.
  5. Try a lower unit figure — say 50 units less — to see how much a small saving is worth each month.

How an electricity bill is calculated

Most Indian homes are charged on a telescopic slab system. Your units are not all charged at one rate. The first block of units is cheap, the next block costs more, and so on. If you use 350 units with the sample slabs, the first 100 units are charged at the lowest rate, the next 200 at the middle rate, and only the last 50 at the higher rate. This is why using a little less power can save more than people expect — the units you cut come off the most expensive slab.

Energy charge = (units in slab 1 × rate 1) + (units in slab 2 × rate 2) + …  ·  Duty = (Energy charge + Fixed charge) × Duty %  ·  Total bill = Energy charge + Fixed charge + Duty

On top of the energy charge, boards add a fixed charge — a flat amount for your connection and sanctioned load, payable even if you use zero units. Then the state government adds electricity duty, a tax charged as a percentage. In this calculator the duty is applied to the energy charge plus the fixed charge, which is how many boards present it; if your board applies duty only to the energy charge, set the fixed charge to zero here and add it to the total yourself. Some bills also carry smaller lines such as meter rent, a fuel adjustment charge (FAC) or arrears — those vary too much by board to build in, so treat the result as a close estimate, not a copy of your bill.

Worked example

A family uses 350 units in a month, on the sample slabs, with a ₹50 fixed charge and 5% duty:

SlabUnitsRateAmount
0–100100₹3.00₹300.00
101–300200₹5.50₹1,100.00
301–35050₹7.00₹350.00

Notice that the last 50 units cost ₹7 each, while the first 100 cost only ₹3 each. Bringing usage down from 350 to 300 units would save the full ₹350 top slab plus duty — about ₹367 in this example.

Sample bills at a glance

Using the same sample slabs, ₹50 fixed charge and 5% duty:

Units usedEnergy chargeTotal bill
100₹300.00₹367.50
200₹850.00₹945.00
300₹1,400.00₹1,522.50
500₹2,800.00₹2,992.50
1,000₹7,050.00₹7,455.00

One unit is one kilowatt-hour: a 100-watt bulb running for 10 hours, or a 1,000-watt heater for 1 hour. Air conditioners, geysers and room heaters are the heavy loads in most homes — a single 1.5-ton AC uses roughly 1.5 units per hour, which is why summer bills jump so sharply.

Frequently asked questions

How is an electricity bill calculated in India?

Your units are priced slab by slab: the first block at the lowest rate, the next block higher, and so on. A fixed charge for your connection is added, and then electricity duty — a state tax — is charged as a percentage. In this calculator, duty is applied to the energy charge plus the fixed charge. Total bill = energy charge + fixed charge + duty.

Are these the real slab rates for my state?

No. The rates filled in here are sample slabs so you can see how the calculation works. Every state and electricity board sets its own tariff, and slabs differ for homes, shops and farms. Your real slabs are printed on your electricity bill or listed on your DISCOM website — type those limits and rates into the slab table and the calculator will follow your tariff.

What is electricity duty?

Electricity duty is a tax that state governments charge on power consumption, usually as a percentage of the bill or as a fixed amount per unit. The percentage differs from state to state and can differ for domestic and commercial connections. It is separate from the rate your electricity board charges for the power itself.

Why is my actual bill higher than this estimate?

Real bills often carry extra lines this calculator does not include: a fuel adjustment charge (FAC or FPPCA) that changes month to month, meter rent, wheeling charges, late-payment surcharges, or arrears from an earlier bill. Some boards also charge duty only on part of the bill or add a minimum monthly charge. Compare the slab-wise energy charge first — if that matches, the difference is in the extra lines.

How can I reduce my electricity bill?

Cut the units that fall in your highest slab, because those cost the most. The biggest loads are usually the AC, geyser, room heater and old refrigerators. Raising the AC setting from 22°C to 26°C, using the geyser for shorter periods, and switching remaining bulbs to LED can easily remove 50–100 units a month. Use the calculator to see what 50 fewer units does to the total.

Can I use this for a shop or office connection?

Yes, if you enter the commercial slab rates, fixed charge and duty for your board. Commercial tariffs often have higher rates and a demand charge based on connected load rather than a simple fixed charge. Enter the demand charge in the fixed charge box as an approximation and the estimate will be close, though not exact.

Do I need an account to use the Electricity Bill Calculator?

No. The Electricity Bill Calculator works without any account or login, and you can use it as many times as you like. There is nothing to install either — it opens directly in your browser.

Can I use the Electricity Bill Calculator on my phone?

Yes. The Electricity Bill Calculator runs in your phone's browser, so there is nothing to download or install. The layout adjusts to small screens and the calculation works exactly the same as on a computer.

Disclaimer: Results are estimates only. The slab rates in this calculator are sample rates, not the official tariff of any electricity board. Please check your bill or your DISCOM for the rates that apply to your connection.